Advanced Search
Search Results
235 total results found
Set camera IP address
Aim To set the IP address of the camera to the same range as the Ethernet card and the computer. Prerequisites You have Axis IP cameras that are supported with MediaRecorder.See Supported IP cameras in Recording devices You installed the Ethernet card.Se...
Set camera password and select power line frequency
Aim To give the camera a password, which is compulsory, and to select the power line frequency of your country. Prerequisites You have Axis IP cameras that are supported with MediaRecorder. See Supported IP cameras in Recording devices You followed ...
Create camera settings
Aim To configure the camera for optimal recording with MediaRecorder. Prerequisites You have Axis IP cameras that are supported with MediaRecorder.See Supported IP cameras in Recording devices You installed the Ethernet card.See Install the Ethernet ...
Create audio settings
Aim To optimize the recording volume. Prerequisites You have Axis IP cameras that are supported with MediaRecorder.See Supported IP cameras in Recording devices You followed the procedure in Ethernet card setup You connected all cameras. You gave the...
Select ONVIF cameras in MediaRecorder
Aim To select a camera that supports ONVIF Profile S in MediaRecorder. If your device does not support ONVIF, see Select devices that do not support ONVIF in MediaRecorder instead. Prerequisites You have Axis IP cameras that are supported with MediaRecor...
Adjust advanced video quality options
Aim To change video quality, for example to reduce the video file size. Prerequisite You experience problems with video quality or data transfer over the network. In all other cases, we recommend not to change the default settings. Procedure Choose File...
Select devices that do not support ONVIF in MediaRecorder
Aim To select a device that does not support ONVIF Profile S in MediaRecorder. If your device does support ONVIF, see Select ONVIF cameras in MediaRecorder instead. Prerequisites Your device does not support ONVIF Profile S You followed the procedure in...
The steps to install GigE cameras
Prerequisites The network allows data transfer of at least 1 Gb per second. We recommend to use a dedicated network for the cameras. The cables must be suitable for Gigabit Ethernet. The minimum cable quality is CAT5e.https://en.wikipedia.org/wiki/Categor...
Connect the GigE cameras to the PC
Prerequisite You have followed the entire procedure in Ethernet card setup in Set up IP cameras No matter how many cameras you use, you need a 1Gb Ethernet interface board (desktop computers only). When you use a 4-port Ethernet board, you can power the c...
Install MediaRecorder with the camera drivers
Aim To install the software that allows communication between your camera and the operating system of the computer with MediaRecorder. Prerequisites You installed the Ethernet card.See Install the Ethernet card in Set up IP cameras You gave the Ether...
Set camera IP address
Aim To make sure that the IP address of the GigE camera and that Ethernet interface board physically connected to that camera match. This ensures reliable data transfer to and from the camera. Prerequisites You followed the procedure in Ethernet card setu...
Configure the cameras
Aim To adjust settings in a Basler GigE camera or USB 3.0 camera, like the video frame rate, video frame resolution, and exposure time, within the camera software. NOTE Settings are stored in the camera software, not on the PC. When you work with multiple c...
The steps to install USB 3 cameras
Prerequisite You have USB 3 cameras that supported with MediaRecorder. See Supported USB cameras in Recording devices Which situation applies to you? You ordered the computer, cameras and MediaRecorder from Noldus IT. In case of Basler USB 3.0 cameras...
Install the USB 3 interface card
MediaRecorder was tested with the following USB 3 interface cards: U3-PCIE1XG205 -1S - You can connect one USB 3 camera to this card. Fresco Logic U3X4-PCIE4XE111 rev 1.1 - You can connect up to four USB 3 cameras to this board. To install the USB...
Install the USB 3 camera driver
Aim To install the software that allows communication between your camera and the operating system of the computer with MediaRecorder. Prerequisites You have the Basler USB 3 camera. You have installed the USB 3 interface card. See Install the USB 3 i...
Connect the USB 3 cameras to the PC
Connect the cameras to the USB 3 interface card of the MediaRecorder computer. TIP USB 3 connectors and ports can be recognized by their blue color coding. Or by a double-S in front of the USB icon. Important note Using multiple Basler USB 3 camer...
Configure the Basler USB 3 camera
Aim To adjust settings in the USB 3 camera, like the video frame rate, resolution, and exposure. NOTE The camera settings are stored by the camera itself, not on the PC. When you work with multiple cameras, repeat the procedure for each camera. Procedure 1...
Summary supported devices
What information are you looking for? Supported devices for EthoVision XT Supported devices for The Observer XT - stationary set-up Supported devices for The Observer XT - portable set-up Supported devices for FaceReader
Supported devices for EthoVision XT
The table below shows the maximum supported (1) resolution, (2) frame rate (fps), (3) color space, (4) number of devices and (5) recording time (hours). All tests were carried out on a Dell Precision T3640 PC with a Euresys Picolo Alert card, card driver Multi...
Supported devices for The Observer XT - stationary set-up
The table below shows the maximum supported (1) resolution, (2) frame rate (fps), (3) number of devices and (4) recording time (hours). Tests were done on a Dell Precision T3620 PC Device Resolution Frame rate Number of devices...